APHEL
- APHEL
- SEAS PRESTIGE
SEAS Prestige APHEL, 2 Way Loudspeaker Kit using the CA22RNY and the 27TBFC/G.
This loudspeaker kit was made with the help of a local DIY enthusiast. It's an old school design with a wide baffle on a large box that is fitted with an 8" woofer and a 1" dome. The inspiration for the kit rests on SEAS kits from the 70's and classic designs from the likes of Snell. This is all about putting the music first and just pure enjoyment.
Drive units
The tweeter is the well proven 1" SEAS Prestige aluminium dome tweeter 27TBFC/G. The aluminium dome is produced in house to meet our strict demands for a consistent performance. It's made with ferrofluid in the air gap to provide good cooling and so that it can be used with a low crossover point. This is quite important when it's matched with a large woofer like it is in this kit.
The low end and midrange is taken care of by the classic SEAS Prestige coated paper cone woofer, CA22RNY. This has a large magnet system to boost the sensitivity, while the coated paper cone deilvers a smooth response all the way up through the midrange. That makes this driver easy to filter and enjoy.
The Enclosure
The enclosure was chosen to be a big 55L box with a wide baffle and a port tuned to 36Hz. This is larger than the traditional QB3 alignment used in many ported designs, but gives the loudspeaker a warm and full bodied bass.
The wider baffle helps to lower the baffle step frequency and to put some more presence into the lower midrange.
Inside the cabinet the walls are fitted with 4mm bitumen and then 10mm of wool felt. Above the lower brace the cabinet is loosely filled with polyester foam all the way to the top. There is no foam around the port, since this dulled the sound too much.
The port in the cabinet can be made longer when you first assemble the kit, and then shorten it after listening to find your optimum bass balance to fit the room and personal preference.
The Crossover
Here we aimed for a slightly tilted response that is favoured by many listeners. This is achieved with a 3rd order filter on both drivers with some resistors to fine tune the slopes. The tweeter also has an L-pad to adjust the sensitivity. On the series resistor for the tweeter we've also put a small shorting capacitor to lift the very top end of the frequency response.
The R3 resistor can be adjusted between 10 Ω and 22 Ω to adjust the tweeter level.
For those who want to experience with their own crossover design or fine tuning, there are some more options. We have added the raw data of the drivers in the cabinet and a setup file for VituixCAD in a zip file for download on top of the page, "Download SEAS APHEL files". Then you can play around with both passive and active designs.
| KIT CONTENT | |||||
| QT | PART # | ITEM | MANUFACTURER | ||
| 2 | 27TBFC/G06 | 26mm AlMg Dome Tweeter H1212 | SEAS PRESTIGE | ||
| 2 | CA22RNY08 | 22cm Paper Cone Woofer H1471 | SEAS PRESTIGE | ||
| 2 | PA820 | 8.2 mfd 250v 21x33 | SOLEN | ||
| 2 | PA3300 | 33 mfd 250v 33x48 | SOLEN | ||
| 2 | PA150 | 1.5 mfd 250v 13x22 | SOLEN | ||
| 2 | PA560 | 5.6 mfd 250v 19x30 | SOLEN | ||
| 2 | S18.27 | .27 mH 1.0 11x22x45 | SOLEN | ||
| 2 | S142.7 | 2.7 mH 1.6 22x45x89 | SOLEN | ||
| 2 | S141.5 | 1.5 mH 1.6 19x38x76 | SOLEN | ||
| 2 | MO1000J2R2 | 2.2 Ohms 10 W | SOLEN | ||
| 2 | MO1000J5R6 | 5.6 Ohms 10W | SOLEN | ||
| 2 | MO1000J15R | 15 Ohms 10W | SOLEN | ||
| 2 | MO1000J4R7 | 4.7 Ohms 10W | SOLEN | ||
| 4 | MO1000J22R | 22 Ohms 10W | SOLEN | ||
| 6 | 322GDS | Crossover Terminal | SOLEN | ||
| 2 | PT-2.5F | Flared Port Tube 2-1/2" x 8-1/2", Adjust Drawing Accordingly | SOLEN | ||
| 1 | DAMPING PAD | Bituminous Felt Damping Pad 39"x39"x1/8" | SOLEN | ||
| 1 | FLEX-XEL S-125 | Felt Material 40"x40"x7/8" | SOLEN | ||
| 1 | POLYESTER | FiberFlex 12"x42"x1.5" | SOLEN | ||
| 2 | DBPPB-CMC | Dual Binding Post Terminal Plate Black | SOLEN | ||
| 4 | 858-LU | Binding Post Gold 8x38mm | SOLEN (CMC) | ||
| 8 | OXSOCKET6X3/4 | Hex Socket Screw #6x3/4" Black | SOLEN | ||
| 8 | OXSOCKET8X1 | Hex Socket Screw #8x1" Black | SOLEN | ||
| 12 | OXSOCKET10X1.25 | Hex Socket Screw #10x1.25" Black | SOLEN | ||
| 16 | CLASSIC1.6 | Tin Plated OFC 2x1.6mm | SUPRA CABLES | ||
| 2 | GFD110-1614B | Female Disconnect .110" 16/14 BLACK | SOLEN | ||
| 2 | GFD110-1614R | Female Disconnect .110" 16/14 RED | SOLEN | ||
| 2 | GFD205-1614B | Female Disconnect .205" 16/14 BLACK | SOLEN | ||
| 2 | GFD205-1614R | Female Disconnect .205" 16/14 RED | SOLEN | ||
| 80 | SCE41BSC | Self Adhesive Foam Tape Black (Gasket Material) | SOLEN | ||